Lab PVC EVA Rubber Mix Mill Plastic Material Two Roll Open Mixing
Mill Equipment
Application:
It is widely used in rubbers and plastics industry for polymer
mixing, such as PVC, color master batch. It consists of roll,
bearing, gap adjusting device, electric control system, safety
device, etc.
ZL-3018 Two roll mill.pdf
Introduction:
Two Roll mill : The two drums rotate, and the prepared samples are
poured along the grooves above the two drums. The baffles on both
sides can also be slightly adjusted as needed. The two rollers are
rotated, and the prepared samples are poured along the grooves
above the two rollers, and the baffles on both sides can also be
slightly adjusted as required. During the operation of the silicone
mill, if there is an emergency, the leg and elbow should
immediately hit the safety door panel, and the built-in control
switch can make the forward rotating double drum reverse
immediately to relieve this dangerous state.
Technical parameters:
| | | | | | | | |
| Roll Hardness | HRC 50 ~ 60 |
| Temperature Accuracy | ± 2 ℃ (we adopt the high accuracy PID micro computer controller)| Model | | ZL-3018-76 | ZL-3018-120 | Zl-3018-160 | ZL-3018-200 | Zl-3018-230 | Zl-3018-300 | ZL-3018-400 | | Diameter of roll | mm | 76 | 120 | 160 | 200 | 230 | 300 | 400 | | Length of roller face | mm | 300 | 350 | 350 | 500 | 650 | 650 | 900 | | Mixing Capacity | kg | 0.002-0.6 | 0.002-2 | 0.002-2.8 | 0.002-5 | 0.005-10 | 1-15 | 5-30 | | Front roll surface speed | rpm | 19 | 19 | 19 | 19 | 19 | 19 | 19 | | Friction ratio | | 1:1.30 | 1:1.35 | 1:1.35 | 1:1.35 | 1:1.27 | 1:1.27 | 1:1.27 | | Roll gap range | mm | 0-3 | 0-6 | 0-6 | 0-8 | 0-12 | 0-12 | 0-15 | | Driving Power | KW | 1 | 1.5 | 2.2 | 7.5 | 11 | 30 | 37 | | Heating Mode | Electricity heating , Oil Heating ( option) | | Cooling Mode | Water Cooling ( option) | | Roll Temperature | Room temperature -- 300℃ |
|
| Safety device | It have 6 safety buttons and safety guard is option |
| Machine weight | kg | 160 | 460 | 660 | 860 | 1960 | 2960 | 3800 |
| Overall dimension | mm | 1100x400x1180 | 1100x550x1380 | 1200x650x1380 | 2200x750x1380 | 2200x950x1580 | 2600x950x1580 | 5295x1789 x170 |
| Power | 380V 3 phase 50-60hz |
Advantage Service:
1. We have R&D, designing department which can not only provide
technological machines but also can satisfy special customized
needs of our clients.
2. Over 50 years’ manufacturing experience, advanced machine and
sophisticated handcraft.
3. There are TWO laboratories in our factory: Environmental
laboratory and Physical laboratory.
4. Our factory have adequate stock monthly, which can meet
customers’ urgent needs.
5. Annual sales over 1,000,000USD; 30,000㎡manufacturing base,
equipped with 120 technicians, we are capable to take large budget
project.
Technical Support:
1. SUS Stainless plate is cut by advanced leaser machine which can
ensure accuracy; All machine appearance is anti-rust electrostatic
painting;
2. Imported electronic components:
ABB/Siemens/Panasonic/Saginomiya/Danfoss/Emkarate/Omron and
imported compressor:BOEK/TECUMSEH, which can keep the machine’s
service life over 10 years.
